Feature
Oscilloscope
Logic Analyzer
Arb. Waveform Generator
Function Picture
|
Model | MSO5054FG |
MSO5054F (
discontinued) |
Acquisition | ||
Sample Rate | Real-Time Sample: 1GS/s | |
Acquisition Modes |
|
|
Normal | Normal data only | |
Peak Detect | High-frequency and randon glith capture | |
Average | Wavefom Average, selectable 4,8,16,32,64,128 | |
Inputs | ||
Inputs Coupling | AC, DC, GND | |
Inpits Impendance | 1MΩ±2% ‖20pF±3pF | |
Probe Attenuation | 1X, 10X | |
Supported Probe Attenuation Factor | 1X, 10X, 100X, 1000X | |
Maximum Input Voltage |
CAT I and CAT II: 300VRMS (10×), Installation
Category; CAT III: 150VRMS (1×); Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz* and above. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above |
|
Horizontal | ||
Sample Rate Range | 1GS/s | |
Waveform Interpolation | (sin x)/x | |
Record Length | 1M | |
SEC/DIV Range | 4ns/div to 40s/div, in a 2, 4, 8 sequence, | |
Sample Rate and Delay Time Accuracy |
±50ppm(at over any ≥1ms time interval) | |
Position Range |
20ns/div
to 80us/div; (-8div x s/div) to 40ms; 200us/div to 40s/div; (-8div x s/div) to 400s; |
|
Delta Time Measurement Accuracy (Full Bandwidth) |
Single-shot, Normal mode:± (1 sample interval
+100ppm × reading + 0.6ns); >16 averages:± (1 sample interval + 100ppm × reading + 0.4ns); Sample interval = s/div ÷ 200 |
|
Vertical | ||
Vertical Resolution | 8-bit resolution, all channel sampled simultaneously | |
Position Range |
2mV/div
to 200mV/div, ±2V 200mV/div to 5V/div, ±50V |
|
Bandwidth | 40MHz; | |
Rise Time at BNC( typical) | 8.8ns; | |
Analog Bandwidth in Normal and Average modes at BNC or with probe, DC Coupled |
2mV/div
to 20mV/div, ±400mV 50mV/div to 200mV/div, ±2V 500mV/div to 2V/div, ±40V 5V/div, ±50V |
|
Math | +, -, *, /, FFT | |
FFT | Windows: Hanning、Flatop、Rectamgular、Bartlett、Blackman; 1024 sample point | |
Bandwidth Limit | 20MHz | |
Low Frequency Response (-3db) | ≤10Hz at BNC | |
DC Gain Accuracy |
±3%
for Normal or Average acquisition mode, 5V/div to 10mV/div; ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div |
|
DC Measurement Accuracy, Average Acquisition Mode |
When
vertical displacement is zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is
selected; When vertical displacement is not zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for s |
|
Volts Measurement Repeatability, Average Acquisition Mode |
Delta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions | |
Trigger System | ||
Trigger Types | Edge, Video, Pulse, Slope, Over time, Alternative | |
Trigger Source | CH1, CH2, EXT, EXT/5, AC Line | |
Trigger Modes | Auto, Normal, Single | |
Coupling Type | DC, AC, Noise Reject, HF Reject, LF Reject | |
Trigger Sensitivity (Edge Trigger Type) |
DC(CH1,CH2,
CH3, CH4): 1div from DC to 10MHz;1.5div from 10MHz to Full; DC(EXT): 200mV from DC to Full; DC(EXT/5):1V from DC to Full; AC: Attenuates signals below 10Hz HF Reject: Attenuates signals above 80kHz; LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz |
|
Trigger Level Range |
CH1,
CH2, CH3, CH4: ±8 divisions from center of screen; EXT: ±1.2V; EXT/5:±6V |
|
Trigger Level Accuracy( typical)Accuracy is for signals having rise and fall times ≥20ns |
CH1,
CH2, CH3, CH4: 0.2div × volts/div within ±4 divisions from center of
screen; EXT: ± (6% of setting + 40mV); EXT/5: ± (6% of setting + 200mV); |
|
Set Level to 50%(typical) | Operates with input signals ≥50Hz | |
Video Trigger |
|
|
Video Trigger Type |
CH1,
CH2, CH3, CH4: Peak-to-peak amplitude of 2 divisions; EXT: 400mV; EXT/5: 2V |
|
Signal Formats and Field Rates, Video Trigger Type | Supports NTSC, PAL and SECAM broadcast systems for any field or any line | |
Holdoff Range | 100ns ~ 10s | |
Pulse Width Trigger |
|
|
Pulse Width Trigger Mode | Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse | |
Pulse Width Trigger Point |
Equal:
The oscilloscope triggers when the trailing edge of the pulse crosses the
trigger level. Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width. Less than: The trigger point is the trailing edge. Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width |
|
Pulse Width Range | 20ns ~ 10s | |
Slope Trigger |
|
|
Slope Trigger Mode | Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope | |
Slope Trigger Point |
Equal:
The oscilloscope triggers when the waveform slope is equal to the set
slope. Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope. Less than: The oscilloscope triggers when the waveform slope is less than the set slope. Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope. |
|
Time Range | 20ns ~ 10s | |
Overtime Trigger |
|
|
Over Time Mode | Rising edge or Falling edge | |
Time Range | 20ns ~ 10s | |
Alternative Trigger |
|
|
Trigger on CH1 | Internal Trigger: Edge, Pulse Width, Video, Slope | |
Trigger on CH2 | Internal Trigger: Edge, Pulse Width, Video, Slope | |
Trigger Frequency Counter |
|
|
Readout Resolution | 6 digits | |
Accuracy (typical) | ±30ppm (including all frequency reference errors and ±1 count errors) | |
Frequency Range | AC coupled, from 4Hz minimum to rated bandwidth | |
Signal Source |
Pulse
Width or Edge Trigger modes: all available trigger sources The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed. Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time. Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity. Video Trigger mode: The Frequency Counter does not work. |
|
Measurement | ||
Cursor Measurement |
Manual:
Voltage difference between cursors: △V Time difference between cursors: △T Reciprocal of △T in Hertz (1/ΔT); Tracing: The valtage and time at a waveform point; |
|
Auto Measuerment | Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF | |
Display | ||
Display Type | 7 inch 64K color TFT (diagonal liquid crystal) | |
Display Resolution | 800 horizontal by 480 vertical pixels | |
Display Contrast | Adjustable (16 gears) with the progress bar | |
Logic Analyzer Specifications | ||
Channels | 8 Channels | |
Max. Input Impendence | 200K(C=10p) | |
Input Voltage Range | 0V~3V | |
Logic Threshold Range | 0V~3V | |
Max. Sample Rate | 500MHz | |
Compatible Input | TTL, CMOS, ECL | |
Sample Depth | 1M | |
Trigger |
|
|
Edge Trigger | D0-D7 select slope (rising or falling edge) | |
Pulse Width | D0-D7 select pulse polarity (positive or negative pulse), trigger when (=, ≠, >, <), trigger pulse width | |
Code-type | D0-D7 select code-type (H, L, X) | |
Duration | D0-D7 select persist time and trigger when (data terminate, data start, and data delay) | |
Queue | D0-D7 select specific data index (0-3) and code-type (H, L, X) | |
Repeat | D0-D7 select code-type (H, L, X) and repeat times | |
Arb. Waveform Generator Specifications (MSO5054FG) | ||
Wave frequency | DC~25MHz | |
DAC clock | 2K~200MHz adjustable | |
Waveform Length | 4KSa | |
Vertical Resolution | 12 bit | |
Frequency stabilization | <30ppm | |
Amplitude | ±3.5V Max. | |
Output impedance | 50 Ω | |
Output current | 50mA Ipeak=50mA | |
System Bandwidth | 25M | |
Wave distortion | -50dBc(1KHz), -40dBc(10KHz) | |
Frequency area | DC~50MHz | |
Input Amplitude | 400mVpp~18Vpp | |
Coupling | DC | |
Frequency precision | ±Time Base Error ±1 Count | |
input impedance | > 100KΩ | |
Pattern Generator | 12Bit | |
Probe Compensator Output | ||
Output Voltage( typical) | About 5Vpp into ≥1MΩ load | |
Frequency(typical) | 1kHz | |
General Features | ||
Supply Voltage |
100-120VACRMS(±10%),
45Hz to 440Hz, CATⅡ 120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ |
|
Power Consumption | <30W | |
Fuse | 2A, T rating, 250V | |
Temperature |
Operating:
32℉ to 122℉ (0℃ to 50℃); Nonoperating: -40℉ to 159.8℉ (-40℃ to +71℃) |
|
Cooling Method | Convection | |
Humidity |
+104℉ or below (+40℃ or below): ≤90% relative
humidity; 106℉ to 122℉ (+41℃ to 50℃): ≤60% relative humidity |
|
Altitude |
Operating:
Below 3,000m (10,000 feet); Nonoperaring: Below 15,000m(50,000 feet) |
|
Size | Length 385mm; Width 200mm; Height 245mm | |
Weight | 3.5KG(with Packing); 2.08KG(without Packing) |
Select | Model | Bandwidth | Channels | Sampling rate | Other |
---|---|---|---|---|---|
DPO7000 Series
|
500MHz 350MHz 200MHz 100MHz |
4-channels oscilloscope 1-channel waveform generator 16-channels logic analyzer |
2GSa/s single channel 1GSa/s half channel 1GSa/s full channels |
Oscilloscope/16-channels logic analyzer/spectrum analyzer/ arbitrary waveform generator/digital voltmeter/ 6-bit frequency meter and accumulator/protocol analyzer 2G storage depth |
|
DSO2000 Series
|
150MHz 100MHz |
2 | 1GSa/s | 2 CH oscilloscope 1 CH 25MHz waveform generator 5 kinds of serial protocol trigger and decode 32 kinds of auto measurements with statistics SCPI remote control 2 sets of DVM |
|
DPO6004B(C)/MPO6004D Series
|
80MHz 100MHz 200MHz |
4CH OSC 2CH AFG 16CH LA DVM FFT Serial Bus triggering and decoder |
1GSa/s | 400000 wfm/s 5 serial decoding option 64M memory depth,up to 80,000 segments 13 kinds of waveforms inside 7 inch WVGA capacitive touch screen |
|
DPO6002B(C)/MPO6002D
|
80MHz 100MHz 200MHz |
2CH OSC 2CH AFG 16CH LA DVM FFT Serial Bus triggering and decoder |
1GSa/s | 400000 wfm/s 5 serial decoding option 64M memory depth,up to 80,000 segments 13 kinds of waveforms inside 7 inch WVGA capacitive touch screen |
|
DSO4004C Series
|
80-250MHz | 4CH +1CH WG+ EXT | 1GSa/s | Oscilloscope + waveform generator 7'' High resolution(800x480); 64K memory depth, USB Host/Device, Support U-disk memory, systom update DVM digital DMM, Auto range |
|
DSO4004B Series
|
80-250MHz | 4CH + EXT | 1GSa/s | Oscilloscope 7'' High resolution(800x480); 64K memory depth, USB Host/Device, Support U-disk memory, systom update DVM digital DMM, Auto range |
|
DSO4000C Series
|
200/100/70MHz | 2CH DSO +1CH GENERATOR + External Trigger |
1GSa/s | Oscilloscope+Waveform Generator , 40K Record Length; 7 inch 64K color LCD display (WVGA 800x480), Integrated USB Host/Device |
|
MSO5000D Series
|
200/100/60MHz | 2CH+16CH(LA)+EXT | 1GSa/s(Analog) 500MSa/s(LA) |
7powerful trigger function, 1M Record Length, USB interface system upgrade, 16CH Logic Analyzer, 7'' LCD WVGA 800*480; VGA Optional |
|
DSO5000P Series
|
200/100/70MHz | 2CH + EXT | 1GSa/s | 40K Record Length, USB interface system upgrade, 7'' LCD WVGA 800*480, Powerful trigger function; |
|
DSO5000B Series
|
200/100/60MHz | 2CH+EXT | 1GSa/s | 1M Record Length, USB interface system upgrade, 7'' LCD WVGA 800*480, 7powerful trigger function; VGA Optional |
|
DSO5000BM Series (Discontinued)
|
200/100/60MHz | 2CH+EXT | 1GSa/s | 2M Record Length, USB interface system upgrade, 7'' LCD WVGA 800*480 7powerful trigger function; VGA Optional |
|
DSO5000BMV Series (Discontinued)
|
200/100/60MHz | 2CH+EXT | 1GSa/s | 2M Record Length, Video Help function; Built in 4G SD Card 7'' LCD WVGA 800*480 7powerful trigger function, USB interface system upgrade; VGA Optional |
|
DPO8000 Series
|
1GHz 800MHz 500MHz 300MHz |
4-channels oscilloscope 1-channel waveform generator 16-channels logic analyzer |
8GSa/s single channel 8GSa/s half channel 4GSa/s full channels |
Oscilloscope/16-channels logic analyzer/spectrum analyzer/ arbitrary waveform generator/digital voltmeter/ 6-bit frequency meter and accumulator/protocol analyzer 2G storage depth |
Model | Description | View Manual |
HT300B,HT500B | 350Mhz,500MHz,10:1/1:1 | Download |
HT100B,HT200B | 100MHz,200MHz,10:1/1:1 | Download |
PP-80,PP-150,PP-200 | 60MHz,100MHz,200MHz,10:1/1:1 | Download |
PP80B, PP150B, PP200B, PP300B | 80Mhz, 150MHz, 200MHz, 300MHz, 10:1/1:1 | Download |
PP-90 | 80MHz,10:1/1:1 | Download |
T3100 | 100MHz,100:1,2000VDC Peak AC | Download |
Model | Description | View Manual |
CC65 | AC/DC: 0 – 20KHz,20mA to 65A DC | Download |
CC650 | AC:0 – 5KHz,1A - 500A ,DC:1A - 650A | Download |
CC800 | AC:0 – 5KHz,1A - 500A ,DC:1A - 800A | Download |